Call today : Phone: 407-608-8015

Financing Available



Press to change to:

Arabic German Portuguese Chinese Italian Russian Japanese Spanish French Korean -


Sign up today to receive our daily sales .

 type e mail address in box and press go

For Email Marketing you can trust

Quantities are limited and all equipment on this web site are subject to prior sale.

                                 Mixers to review




APV/BP horizontal tilt bowl dough mixer

2000lb Capacity  fully remanufactured


One (1) ¡°APV/BP¡± horizontal tilt bowl dough mixer, model BPX 2000, Machine number 1416-03-005, as shown in both the attached brochure and the APV drawing, with the following features

Ø     Nominal 2000 lb mixing capacity of 62% absorption bread doughs.

Ø     140º over-tilt mixing bowl, electro-mechanical type bowl drive, with pneumatic bowl position lock included.

Ø     All S/S mixing bowl, bowl canopy and exterior cabinet.

Ø     Single side 125/62.5-hp heavy duty motor drive for the mixing agitator with a multi V-belt connection to the shaft mounted heavy duty inline gearbox. 

Ø     Three (3) roller bar type agitator with split hub s/s ¡°spiders¡±, with three inner roller bars positioned inside of the outer roller bars.

Ø     S/S jacketed mixing bowl, serpentine type, for glycol cooling.

Ø     Three [3] liquid inlets and a bulk flour inlets on the S/S bowl canopy, with a vent sock connection included.

Ø     Sanitary type lip seals on main agitator shaft, easy access type.

Ø     Custom heavy duty raised pedestal type mounts, two (2) total.

Ø     Hinged and ¡°lift off,¡± s/s side doors with electrical safety interlocks.

Ø     NEMA 4X, S/S, rear mounted electrical starter panel, with disconnect switch.

Ø     Unit mounted operators control station on front of mixer.

Ø     Heavy duty S/S dough trough bumper under front lip of bowl.

Was fully remanufactured, including but not limited to the following work as completed:

Ø     Rebuilt main agitator motor and tilt bowl motor and rebuilt tilt bowl gear boxes with all new bearings and seals installed.

Ø     Rebuilt bowl jacket, reinforced mixing bowl, hydrostatic pressure tested to 250 PSI, re-insulated bowl with Armaflex closed cell foam rubber, and  re-installed the s/s bowl ¡°cover skin¡±.

Ø     Replaced the main shaft bearings and seals with ¡°new¡±.

Ø     Installed ¡°new¡± main shaft drive V-belt assemblies.

Ø     Rebuilt bulk flour inlet butterfly gate with pneumatic cylinder and ¡°new¡± three-way pneumatic valve, rotated 90 degrees to accommodate the manual ingredient feed opening.

Ø     ¡°New¡± roller bar bushings installed.

Ø     Rebuilt pneumatic bowl locking system.

Ø     Replaced any worn sprockets with ¡°new¡±.

Ø     Built an all ¡°new¡± operator¡¯s control station with a New AB Panelview Plus 600 color and install all ¡°new¡± machine mounted electrical devices throughout, including the AB Micrologix PLC

Ø     Rebuilt main remote control panel to be 480-volt, 3-Ph primary power, using all ¡°new¡± electrical controls and remanufacturing the main electrical starter.

Ø     Polished out all s/s surfaces.

Ø     Re-coated all mild steel surfaces in ¡°Steel-It¡± s/s coating.

Ø     Reinforced bowl mixing canopy to minimize flexing.

 INV# 18200DM07062010

Hit Counter

06/23/2014 11:50:15 AM

 Production Line Equipment. All rights reserved.